Shop / Kits
Build a robot car that steers around obstacles by itself. Every kit comes with its simulation twin: run and tweak the code in simulation first, then wire the real one.
Coming soon · DIY kit · ESP32
Get notified when pre-orders open
We are building and testing the first real kit now. Pre-orders open after it passes our tests. One email when they open.
Why this kit is different
Many robot car kits come with a custom all-in-one board. Everything is pre-wired, so it works the moment you plug it in, but you never see how. We go the other way: you start from the basic parts, a microcontroller, a motor driver, an ultrasonic sensor and two motors, and connect them yourself, step by step. By the time your car drives, you know what every part does and why it is wired that way.
- Standard parts you can buy anywhere, so what you learn carries over to your next project.
- Every step explains the part: how the driver turns a small signal into motor power, how the sensor measures distance with sound, how the encoders count wheel turns.
- Nothing hidden: open code, an open wiring diagram, and a simulation twin you can take apart.
- Learn from real failures: every chapter shows the problems we actually ran into while building our test car, what we measured and how we fixed it. Each one ends with a troubleshooting table: symptom, likely cause, how to check, how to fix.
One example from our first motor test: we switched the battery off, and the motor kept spinning. With only the USB cable plugged in, the computer was powering the motor backwards through the board. On an all-in-one board you would never see why. In this kit, the manual shows you exactly where the power goes, and the one simple rule that prevents it.
What it does
The car drives forward, measures the distance ahead with an ultrasonic sensor, and turns away before it hits anything. You write and change the code yourself, so you can make it smarter: slow down near walls, pick the more open side, or follow a wall.
Sim first, then the real robot
Every kit comes with its simulation twin. Start with a quick 2D twin that runs in seconds on any computer: run the obstacle-avoiding code, tune it, and see what happens when you change a number. In the advanced chapters you move to a MuJoCo physics twin of the same car, where wheel slip, inertia and motor response show up too. Then upload the same logic to the real ESP32.
Choose your plan
Both plans build the same car. Pick how much you want to learn along the way. Tap a plan to see exactly what you get.
Prices in US dollars, shipping not included. Pre-orders are not open yet.
Learning · US$79
Understand why it moves
For students, self-learners and teachers. The full hardware kit with the manual, wiring card, code and simulation twins, plus step-by-step video lessons that explain each part as you build it, and exercises where you change the code yourself.
You get
- The full hardware kit (see below)
- Step-by-step assembly manual, wiring diagram and printed wiring card
- Complete, ready-to-run Arduino code
- Troubleshooting tables: symptom, likely cause, how to check, how to fix
- Simulation twins of the car: a quick 2D twin and a MuJoCo physics twin
Video lessons
- GPIO: how the ESP32 talks to the other parts
- PWM: how a digital pin controls motor speed
- Motor driver: how the L298N turns a small signal into motor power
- Ultrasonic ranging: measuring distance with sound
- Obstacle avoidance logic: how the car decides where to turn
- Hands-on exercises: modify the code and see what changes
Every chapter shows
- The simulation twin first, then the real car
- The most likely failure, with our measured numbers
- How to fix it
We are filming the lessons now.
Bring your own parts · US$35
Video lessons only
For makers who already own the parts, or prefer to buy them locally. You get every lesson and file from the Learning plan, plus a hardware list so you can source the same parts yourself.
You get
- All Learning video lessons and exercises
- Assembly manual, wiring diagram and full code
- Troubleshooting tables
- 2D and MuJoCo simulation twins
- Hardware list with the exact specs we tested
Not included
- Any physical parts or 3D-printed chassis
Using different parts? The lessons still apply, but pins and numbers may differ from ours.
Compare plans
| Learning | Own parts | |
|---|---|---|
| Hardware kit | Yes | No |
| Manual, wiring diagram, code | Yes | Yes |
| Troubleshooting tables | Yes | Yes |
| Simulation twin | Yes | Yes |
| Video lessons | Yes | Yes |
| Code exercises | Yes | Yes |
| Price | US$79 | US$35 |
Join the waitlist for your plan
Pre-orders are not open yet. Choose the plan you want and we will email you once, when they open.
What's in the box
Learning plan.

Main parts
- ESP32 DevKit V1 (ESP-WROOM-32, CP2102, USB-C) with an expansion board
- L298N motor driver
- HC-SR04 ultrasonic sensor with mount
- 2 × JGA25-370 6 V gear motors with Hall encoders
- 2 × motor brackets
- 2 × wheels, 68 × 27 mm
- Ball caster
- 3D-printed chassis with caster mount
- 2 × 18650 battery holder with switch
Other: wires, batteries, screws
- Jumper wires: 10 female-to-female, 2 male-to-female
- 2 × encoder cables
- USB-C data cable
- Screws and nuts: 30 × M3×10, 4 × M3×5, 30 × M3 nuts
- 18650 batteries: not included. You need two. We recommend the Panasonic NCR18650GA (see below).
Tools

- In the kit: Phillips screwdriver and socket
- You provide: needle-nose pliers, wire stripper, a multimeter (optional, recommended) and an 18650 Li-ion smart charger
Also included
- Printed wiring card and a QR code to the full online manual (English and Traditional Chinese)
- Download: the 2D and MuJoCo simulation twins and the complete Arduino code
Designed to build without soldering: screw terminals, jumper wires and screws only. 18650 batteries are not included in any kit. See the recommended battery and charger below. Electronics kit for ages 14+; younger builders need adult supervision.
Recommended battery & charger
Batteries and chargers are not included. These are the ones we recommend for Kit 1.
Battery
- Model
- Panasonic NCR18650GA
- Type
- 18650 Li-ion rechargeable battery
- Nominal voltage
- 3.6 V
- Typical capacity
- 3450 mAh
Charger
- Type
- External 18650 Li-ion smart charger
- Charging voltage
- 4.2 V
- Charging method
- CC/CV
- Recommended current
- 1 A–1.5 A
- Cell support
- Must support unprotected Li-ion cells
Important safety notice
Use only compatible Li-ion chargers designed for 4.2 V charging. Do not use NiMH or other incompatible battery chargers. Always follow the battery manufacturer's safety instructions.
Payment and shipping
Pre-orders will open here on tinybotforge.com. We plan to ship worldwide with PayPal for international orders, and bank transfer, credit card and cash on delivery at convenience stores in Taiwan. Shipping costs, pre-order terms and the return policy will be published on this page before pre-orders open.
Questions? [email protected]