TINYBOT FORGE

Kit 1: ESP32 obstacle-avoiding car

Animation only, not a real photo.

Shop / Kits

Build a robot car that steers around obstacles by itself. Every kit comes with its simulation twin: run and tweak the code in simulation first, then wire the real one.

Coming soon · DIY kit · ESP32

Get notified when pre-orders open

We are building and testing the first real kit now. Pre-orders open after it passes our tests. One email when they open.

One email at launch. Unsubscribe anytime.

Why this kit is different

Many robot car kits come with a custom all-in-one board. Everything is pre-wired, so it works the moment you plug it in, but you never see how. We go the other way: you start from the basic parts, a microcontroller, a motor driver, an ultrasonic sensor and two motors, and connect them yourself, step by step. By the time your car drives, you know what every part does and why it is wired that way.

One example from our first motor test: we switched the battery off, and the motor kept spinning. With only the USB cable plugged in, the computer was powering the motor backwards through the board. On an all-in-one board you would never see why. In this kit, the manual shows you exactly where the power goes, and the one simple rule that prevents it.

What it does

The car drives forward, measures the distance ahead with an ultrasonic sensor, and turns away before it hits anything. You write and change the code yourself, so you can make it smarter: slow down near walls, pick the more open side, or follow a wall.

Animation only, not real footage.

Sim first, then the real robot

Every kit comes with its simulation twin. Start with a quick 2D twin that runs in seconds on any computer: run the obstacle-avoiding code, tune it, and see what happens when you change a number. In the advanced chapters you move to a MuJoCo physics twin of the same car, where wheel slip, inertia and motor response show up too. Then upload the same logic to the real ESP32.

Choose your plan

Both plans build the same car. Pick how much you want to learn along the way. Tap a plan to see exactly what you get.

Prices in US dollars, shipping not included. Pre-orders are not open yet.

Learning · US$79

Understand why it moves

For students, self-learners and teachers. The full hardware kit with the manual, wiring card, code and simulation twins, plus step-by-step video lessons that explain each part as you build it, and exercises where you change the code yourself.

You get

  • The full hardware kit (see below)
  • Step-by-step assembly manual, wiring diagram and printed wiring card
  • Complete, ready-to-run Arduino code
  • Troubleshooting tables: symptom, likely cause, how to check, how to fix
  • Simulation twins of the car: a quick 2D twin and a MuJoCo physics twin

Video lessons

  • GPIO: how the ESP32 talks to the other parts
  • PWM: how a digital pin controls motor speed
  • Motor driver: how the L298N turns a small signal into motor power
  • Ultrasonic ranging: measuring distance with sound
  • Obstacle avoidance logic: how the car decides where to turn
  • Hands-on exercises: modify the code and see what changes

Every chapter shows

  • The simulation twin first, then the real car
  • The most likely failure, with our measured numbers
  • How to fix it

We are filming the lessons now.

Bring your own parts · US$35

Video lessons only

For makers who already own the parts, or prefer to buy them locally. You get every lesson and file from the Learning plan, plus a hardware list so you can source the same parts yourself.

You get

  • All Learning video lessons and exercises
  • Assembly manual, wiring diagram and full code
  • Troubleshooting tables
  • 2D and MuJoCo simulation twins
  • Hardware list with the exact specs we tested

Not included

  • Any physical parts or 3D-printed chassis

Using different parts? The lessons still apply, but pins and numbers may differ from ours.

Compare plans

LearningOwn parts
Hardware kitYesNo
Manual, wiring diagram, codeYesYes
Troubleshooting tablesYesYes
Simulation twinYesYes
Video lessonsYesYes
Code exercisesYesYes
PriceUS$79US$35

Join the waitlist for your plan

Pre-orders are not open yet. Choose the plan you want and we will email you once, when they open.

Which plan do you want?

One email when pre-orders open. Unsubscribe anytime.

What's in the box

Learning plan.

Kit 1 parts laid out: a bag of screws and nuts, two gear motors with encoders, motor brackets, a 2 × 18650 battery holder, L298N motor driver, HC-SR04 ultrasonic sensor with acrylic mount, ESP32 board and expansion board, ball caster, USB cable, encoder cable, two bundles of jumper wires, two wheels, a 3D-printed mount and the grey 3D-printed chassis
Real photo of our Kit 1 parts. The printed wiring card is not shown. 18650 batteries are not included.

Main parts

Other: wires, batteries, screws

Tools

A red digital multimeter, two Panasonic NCR18650GA batteries, a cross-shaped socket wrench and a Phillips screwdriver
In the kit: the Phillips screwdriver and socket. Not included, shown for reference: the multimeter and the two NCR18650GA batteries.

Also included

Designed to build without soldering: screw terminals, jumper wires and screws only. 18650 batteries are not included in any kit. See the recommended battery and charger below. Electronics kit for ages 14+; younger builders need adult supervision.

Recommended battery & charger

Batteries and chargers are not included. These are the ones we recommend for Kit 1.

Battery

Model
Panasonic NCR18650GA
Type
18650 Li-ion rechargeable battery
Nominal voltage
3.6 V
Typical capacity
3450 mAh

Charger

Type
External 18650 Li-ion smart charger
Charging voltage
4.2 V
Charging method
CC/CV
Recommended current
1 A–1.5 A
Cell support
Must support unprotected Li-ion cells

Important safety notice

Use only compatible Li-ion chargers designed for 4.2 V charging. Do not use NiMH or other incompatible battery chargers. Always follow the battery manufacturer's safety instructions.

Payment and shipping

Pre-orders will open here on tinybotforge.com. We plan to ship worldwide with PayPal for international orders, and bank transfer, credit card and cash on delivery at convenience stores in Taiwan. Shipping costs, pre-order terms and the return policy will be published on this page before pre-orders open.

Questions? [email protected]